Camera Models

• FLIR Camera warranty and service information

  Warranty coverage and service information for FLIR cameras used with Swing Catalyst

• How to configure AVT Manta/Prosilica GigE highspeed cameras

  Swing catalyst support AVT high-speed GigE machine vision cameras. These cameras connect to the computer through a gigabit network interface/cable and allow…

• How to configure IDS uEye GigE camera with Swing Catalyst

  Guide to configuring IDS uEye GigE cameras with Swing Catalyst. For USB camera setup, see the IDS uEye USB article.

• How to configure Point Grey / FLIR GigE (Blackfly) camera's with Swing Catalyst

  Guide to configuring Point Grey / FLIR GigE Blackfly cameras with Swing Catalyst.

• How to find what standards your cameras support for use with Halcon

  Usually the manufacturer will mention what standards they support explicitly either in documentation or if the documentation or marketing material contain…

• How to install AVT Manta/Prosilica GigE cameras

  To setup and install GigE cameras you will require one or more free network ports in your computer.

• How to set static IP on FLIR Blackfly GigE cameras

  Each camera and network adapter must have its own unique static IP address. For example, if you assign a static IP addresses to a cameras, ensure that the…

• How to set static IP on Lynx GigE cameras

  Once the cameras have static IP addresses assigned to them you need to configure the network adapters you plan on using with a static IP. This needs to be…

• How to set up Basler GigE camera's with Swing Catalyst

  Each camera and Ethernet card (NIC / Network interface controller) should be configured with static IP's on different subnets (and subnet mask)

• How to setup Halcon for Swing Catalyst

  The release of Swing Catalyst 6.0 brings support for three of the most common machine vision standards.

• How to setup iDS uEye USB highspeed cameras

  This support article will describe how to install and setup a USB 2.0 or 3.0 camera for use in Swing Catalyst.

• How to upgrade or downgrade Fox / Lynx firmware

  How to upgrade or downgrade firmware on Swing Catalyst Fox and Lynx cameras

• How to use IDS uEye USB cameras with Swing Catalyst

  This support article describes the practical details of how to configure and use a IDS uEye USB camera.

• How to use Point Grey / FLiR USB cameras with Swing Catalyst

  Note: Camera control settings are limited to FlyCapture (Point Grey software).

• How to use the Dragon (120 FPS) USB 2.0 camera with Swing Catalyst

  This article covers how to setup and use the Dragon USB 2.0 camera with Swing Catalyst.

• Setting up FLIR BlackFly S GigE in Swing Catalyst

  This article covers how to use Spinnaker compatible GigE Vision cameras in Swing Catalyst.

• Setting up FLIR BlackFly S USB in Swing Catalyst

  This article covers how to setup and configure a Spinnaker compatible USB camera in Swing Catalyst.

• Setting up the Swing Catalyst Fox USB 3.0 camera(s)

  Guide to assembling and setting up Swing Catalyst Fox USB 3.0 cameras, including driver installation and configuration

• Setting up the Swing Catalyst Lynx GigE camera(s)

  Both the "Lynx" and "Fox" cameras are only supported in Swing Catalyst 9.8.2 or higher.

• Setting up Ximea USB3 Vision camera's with Swing Catalyst

  How to set up Ximea USB3 Vision cameras with Swing Catalyst

• Upgrading the firmware on the FLIR Blackfly S

  This article covers how to upgrade the firmware on the FLIR Blackfly S GigE BFS-PGE-04S2C-CS.

• Using FLIR Blackfly S (Spinnaker) cameras with Swing Catalyst

  This support article covers setting up FLiR Blackfly S cameras with Swing Catalyst 9.4.